Alberta Septic Fields/Tanks and Freezing

Question#2: How do I keep my septic field or tank from freezing?

Thanks to Martin for asking this question.

A septic system is a highly efficient, self-contained, underground wastewater treatment system. Because septic systems treat and dispose of household wastewater onsite, they are often more economical than centralized sewer systems in rural areas where lot sizes are larger and houses are spaced widely apart.

Alberta Septic Tank Installation

Septic systems are also simple in design, which make them generally less expensive to install and maintain. And by using natural processes to treat the wastewater onsite, usually in a homeowner’s backyard, septic systems don’t require the installation of miles of sewer lines, making them less disruptive to the environment.

A septic system consists of two main; a septic tank and a drain-field. The septic tank is a watertight box, usually made of concrete or fiberglass, with an inlet and outlet pipe. Wastewater flows from the home to the septic tank through the sewer pipe. The septic tank treats the wastewater naturally by holding it in the tank long enough for solids and liquids to separate. The wastewater forms three layers inside the tank. Solids lighter than water (such as greases and oils) float to the top forming a layer of scum. Solids heavier than water settle at the bottom of the tank forming a layer of sludge. This leaves a middle layer of partially clarified wastewater.

The layers of sludge and scum remain in the septic tank where bacteria found naturally in the wastewater work to break the solids down. The sludge and scum that cannot be broken down are retained in the tank until the tank is pumped.

The layer of clarified liquid flows from the septic tank to the drain-field or to a distribution device, which helps to uniformly distribute the wastewater in the drain-field. A standard drain-field (also known as a leaching field, disposal field, or a soil absorption system) is a series of trenches or a bed lined with gravel or course sand and buried one to three feet below the ground surface. Perforated pipes or drain tiles run through the trenches to distribute the wastewater. The drain-field treats the wastewater by allowing it to slowly trickle from the pipes out into the gravel and down through the soil. The gravel and soil act as biological filters.

The use of septic fields goes back a hundred years or so. The first ones were very simple holding containers that would eventually leach into the ground. I even saw a septic tank made out of an old car (I wish I had pictures of it). Anyway the tank and piping of a septic tank usually are not buried very deep. Typically between 18″ to 36″ for the pipe and 6′ to 8′ for the bottom of the tank.

As long as the tank is being used you should have no problems with the tank or lines freezing. The bacteria that break down the effluent (poo and other assorted materials) create quite a bit of heat which keeps everything toasty. I couple of rules to remember though.

  1. Keep all traffic off the drain line from the house to septic, the septic tank and field. That includes foot traffic, horses, cars, anything with weight to it that can drive the frost further into the ground causing freeze ups
  2. Straws bales can be your best friend. Piling bales over the tank and building sewer can further insulate the lines and protect them
  3. Keep your field manicured (cut the grass). This helps aid the transfer of gases that the bacteria create to the atmosphere and will keep your field fit and operational

Some Do Not’s

  1. Do not add anti-freeze, salt or a spetic additive to system
  2. Do not pump sewage to the surface
  3. Do not start a fire over the system to unthaw
  4. Do not run water continually to unfreeze

A typically system looks something like this.

Alberta Septic Tank Installation

Some of the restrictions for installing a septic fields are outlined here.

Septic tank installation set-backs

Trouble with Hot Water Tanks

Here’s some straight talk and practical advice on how you could repair water heater problems. No hot water coming from the faucet, puddles of discolored water close to the heater tank and banging, popping, gurgling, boiling or other strange sounds coming from the tank are all signs that problems with your system have crept up on you. Because there are many things that can cause problems with your water heating system, it is a good idea to call on a professional to diagnose and repair your tank.

Learning how to repair water heater problems yourself can help you to avoid costly mistakes. If you are on a shoestring budget, early diagnosis is key, but before we go any further, a word of caution: If you go near the unit and smell natural gas (a rotten egg type smell), immediately turn off the pilot light and close the gas shutoff valve. Contact a licensed, certified plumber right away for help with the problem.

Now, one of the most common issues with these systems is that it is not doing its primary job. It is important to remember that gas heaters work much differently than electric heaters and the types of solutions to problems will not then be the same. That said, if you water heater stops giving you enough hot water, the tank may need to be flushed to ensure that mineral deposits are not bringing down the efficiency.

If your hot water is too hot, a plumber can find out exactly what is causing the problem and take necessary steps to repair water heater problems such as replacing your tanks thermostat. By the same token, water heater leaks should be diagnosed by professional plumbers because there is no one cause. Usually the problem with noisy tank heaters is an accumulation of minerals due to hard water.

A plumber may be able to repair the problem by flushing the sediment from the tank. But often it is too late by this time and the heater must be replaced. Foul smelling water that smells like sulfur may mean that your anode rod has been damaged and needs to be replaced by a plumber.

If you find that the water is dis-coloured, in most instances, it is often the result of iron, copper and other minerals being dispersed into the water in your hot water tank. Installing a whole house water filter and flushing the tank will help with this problem. It is also a good idea to have a water softener installed as well.

With all of this in mind, it may be that the most cost efficient way to repair water heater problems is to contact a plumber. Be sure to check the validity of the plumber’s business license and that they are insured. With proper maintenance and care your water heater can provide you with at least 10 years of good service. However, when there is a problem, let an expert plumber be your first line of defense.

Give us a call at 403-279-7554 or book online.